2020 Salsco, Inc. Engine Driven, Hydraulic Feed Chippers 810

Information

2020 Salsco, Inc. Engine Driven, Hydraulic Feed Chippers 810

Model 810 Chipper is a single feed roll unit (Dual Feed Rolls are available as an option) with an extra wide 18" x 10" high opening at the feed roll. Piles of brush, limbs and branches up to 10" round wood can be fed into this unit quickly and efficiently. Performance and durability is the trademark of all our chippers, and the 810 is proof of this philosophy.

Drain plugs on all tanks, diamond plate fenders with light enclosures, 360º exhaust chute, lockable tanks and engine enclosures, are just some of the standard features of this unit.

Safety Latch on the impeller, Safety Apron welded to the bottom of the infeed tray, Emergency Stop Buttons on either side of the infeed tray, Safety Bar mounted on the outer edge of the infeed which is accessible from both sides as well as the top of the infeed and SSS Salsco Safety Shield are all safety features that are standard on the Model 810.

The SSS Salsco Safety Shield is a safety system that vastly improves wood chipping safety, proactively and effectively preventing wood chipper injury by shutting down the chipper’s infeed system when an operator enters a defined hazard zone.

Photos

Highlights

  • Eldersburg, Maryland
  • 2020
  • Salsco, Inc.
  • Engine Driven, Hydraulic Feed Chippers 810
  • Hatz | Kubota
  • Fenders: 3/8” thick steel diamond plate fenders with light enclosures.
  • Available
  • 8’ | Infeed Tray: 57”
  • 7' | Infeed Tray: 33”

Specifications

  • 2020
  • Salsco, Inc.
  • Engine Driven, Hydraulic Feed Chippers
  • 810
  • Brush
  • Hatz | Kubota
  • Tier IV
  • 37HP Briggs & Stratton
  • Single plate over-center clutch.
  • One (1) 5-V single back belt. Cast iron pulleys with taper lock centers.
  • Hoses: SAE JIC hose ends & fittings. 3,000 P.S.I. working, 12,000 P.S.I. burst. | Motors: Eaton Char-Lynn, H Series, 14.1 Cu. In. Disp.
  • Eaton, 7 GPM Gear Pump, 1.20 Cu. In. Disp.
  • Two (2), ST225/80R16 LR “E”, 10 Ply
  • 12 v., automotive type, 900 cold cranks. Lockable battery box.
  • Fenders: 3/8” thick steel diamond plate fenders with light enclosures.
  • 2” x 3” X 3/16” wall rectangular steel tubing.
  • Six (6) position, adjustable height hitch
  • Infeed Opening: Opening at feed roll 10” high x 18” wide to accept 10” round wood. | Impeller Housing: Upper, lower, front & rear side housing is 3/8” steel plate.
  • Exhaust Chute: 360° hand crank swivel, height adjustable exhaust chute with easy adjust 12” long directional exhaust flap. Continuous welds.
  • 2-5/16” ball or 3” pintle
  • 17’ 9”
  • 8’ | Infeed Tray: 57”
  • 7' | Infeed Tray: 33”
  • 24 gallon steel
  • 15 gallon steel tank
  • 6,000 lb. Torflex
  • 5,000 lbs. (Approximately)
  • Jack: 2,000 lb. capacity, adjustable height, top wind, snap swivel stand.
  • Two (2), Bridgestone rubber tracks.