2020 Salsco, Inc. Engine Driven, Hydraulic Feed Chippers 810M

Current Salsco, Inc. Wood-Chippers Engine Driven, Hydraulic Feed Chippers

Swipe to View More

Year 2020
Make Salsco, Inc.
Model Engine Driven, Hydraulic Feed Chippers
Engine Kubota | Briggs & Stratton

Year 2020
Manufacturer Salsco, Inc.
Model Name Engine Driven, Hydraulic Feed Chippers
Trim Name 810M
Generic Type (Primary) Brush
Engine Kubota | Briggs & Stratton
Emissions Tier IV
Engine Power 37.6 HP | 37 HP

810M has an extra wide 18" infeed opening to handle huge amounts of brush with ease. The infeed handle has a full reverse, neutral, slow and fast speed and is easily accessible from either side of the infeed. Double bed knives, one horizontal and one vertical, are adjustable and sharpenable and provide excellent chipping power when processing vines, palm fronds and evergreens.

Safety Latch on the impeller, Safety Apron welded to the bottom of the infeed tray, Emergency Stop Buttons on either side of the infeed tray, Safety Bar mounted on the outer edge of the infeed which is accessible from both sides as well as the top of the infeed and the SSS Salsco Safety Shield are all safety features that are standard on Model 810M.

The SSS Salsco Safety Shield is a safety system that vastly improves wood chipping safety, proactively and effectively preventing wood chipper injury by shutting down the chipper's infeed system when an operator enters a defined hazard zone.

Engine

Engine Kubota | Briggs & Stratton

Emissions Tier IV

Engine Power 37.6 HP | 37 HP

Drivetrain

Clutch Kubota: Single plate clutch | Briggs & Stratton: Centrifugal clutch

Drive System One (1) 3-V single back belt. Cast iron pulleys with taper lock centers.

Hydraulics

Hydraulic Type Hoses: SAE JIC hose ends & fittings. 3,000 P.S.I. working, 12,000 P.S.I. burst. | Motors: Eaton Char-Lynn, H Series, 14.1 Cu. In. Disp.

Pump Type Eaton, 7 GPM Gear Pump, 1.20 Cu. In. Disp

Wheels & Tires

Tires, Rear Specification ST225/75R15, radial, 9.5” x 16”, load range “D”.

Battery

Battery 12 v., automotive type, 900 CCA. Lockable & cushioned box.

Chassis

Mainframe 2” x 3” x 3/16” wall, rectangular steel tubing, continuous welds. 3” x 4” main center beam. All cross members fully gusseted

Hitch/Type Six (6) position, adjustable height

Chassis Fenders: 3/8” thick steel diamond plate fenders with light enclosures

Dimensions

Adjustability Exhaust Chute: 360º rotation, fixed height exhaust chute with adjustable 12” long directional chip deflector. No tools necessary to adjust.

Dimensions Infeed Opening: 10” high x 18” wide to accept 10” round wood. | Impeller Housing: 3/8” steel plate upper & lower housing, front & rear side housing. Upper housing is vented to provide more air flow for chip exhaust

Coupling 3” pintle, or 2-5/16” ball

Length 15’

Width 6’ | Infeed Tray: 57”

Height 7’ 7” | Infeed Tray: 33”

Capacities

Fuel Capacity 24 gallon lockable, cushioned tank with drain plug and screw cap with dipstick.

Hydraulic Capacity 15 gallon fuel tank with a drain plug & screw cap with dipstick.

Axle Capacity, Rear 6,000 lb. Torflex

Weights

Weight 4,520 lbs. (Approximately)

Features

Features Jack: 2,000 lb. capacity, adjustable height, top wind, snap swivel jack stand.

2020 Salsco, Inc. Engine Driven, Hydraulic Feed Chippers 810M