Current Salsco, Inc. Wood-Chippers Engine Driven, Hydraulic Feed Chippers

2020 Salsco, Inc. Engine Driven, Hydraulic Feed Chippers 813

2020 Salsco, Inc. Engine Driven, Hydraulic Feed Chippers 813

Swipe to View More

  • Year 2020
  • Make Salsco, Inc.
  • Model Engine Driven, Hydraulic Feed Chippers
  • Engine Hatz | Kubota
Shop Salsco, Inc. Pre-Owned
Product Details Specifications Photos
2020 Salsco, Inc. Engine Driven, Hydraulic Feed Chippers 813

2020 Salsco, Inc. Engine Driven, Hydraulic Feed Chippers 813

  • Year 2020
  • Manufacturer Salsco, Inc.
  • Model Name Engine Driven, Hydraulic Feed Chippers
  • Trim Name 813
  • Generic Type (Primary) Brush
  • Engine Hatz | Kubota
  • Emissions Tier IV
  • Engine Power 74HP | 74.3HP

2020 Salsco, Inc. Engine Driven, Hydraulic Feed Chippers 813

Model 813 is a single feed roll unit with an extra wide 18" opening. Performance and durability is the trademark of this unit. Drain plugs on all tanks, fenders with light enclosures, 360º exhaust chute, lockable tanks and a full lockable engine enclosure, are just some of the standard features of this unit. All the basic components are included in base unit. Engine options include both gas and diesel engine packages.

Model 813 is built with the operator in mind, and will perform consistently and efficiently day after day.

Engine

Engine Hatz | Kubota
Emissions Tier IV
Engine Power 74HP | 74.3HP

Drivetrain

Clutch Single plate or double plate over-center clutch depending on horse power for diesel engine options. Autoclutch on PSI gas engines.

Hydraulics

Hydraulic Type Hoses: SAE JIC hose ends & fittings. 3,000 P.S.I. working, 12,000 P.S.I. burst. | Motors: One (1) Eaton Char-Lynn, Series H, 14.1 Cu.In.Disp
Pump Type One (1) Eaton Gear pump, 5/8” 9-tooth spline shaft, 66 Cu.In.Disp.

Battery

Battery 12 v., automotive type, 900 cold cranks. Lockable battery box.

Chassis

Mainframe 3/8” thick steel diamond plate fenders with light enclosures and flag holders
Hitch/Type Adjustable height
Chassis Fenders: Extra heavy duty 1/4” thick diamond plate fenders with safety light guards.

Dimensions

Adjustability Exhaust Chute: 360º rotation, fixed height exhaust chute with adjustable chip deflector. No tools necessary to adjust.
Dimensions Infeed Opening: Opening at feed roll, 13” high x 18” wide to accept 13” round wood. | Impeller Housing: Upper, lower, front & rear side housing is 3/8” steel plate. Housings are hinged & held in place by a 13” long x 3/4” diameter pin. Impeller inspection door. Upper housing is vented to provide more air flow for chip exhaust.
Coupling 2-5/16” ball or 3” pintle
Length 17’ 6”
Width 7’ | Infeed Tray: 57”
Height 8’ | Infeed Tray: 33””

Capacities

Fuel Capacity 24 gallon steel
Hydraulic Capacity 16-3/4 gallon steel tank, drain plug, lockable, vented, screw cap with dipstick.
Axle Capacity, Rear 7,000 lb. Torflex | 8,000 lb. Torflex

Weights

Weight 7,500 lbs. (Approximately)

Features

Bearing Hanger Type 4-bolt, heavy duty, cast iron, greaseable & self-centering
Features Jack: Side wind swivel snap ring mount. 2,000 lb. lift

Product Photography