2020 Salsco, Inc. Engine Driven, Hydraulic Feed Chippers 813XT

Information

2020 Salsco, Inc. Engine Driven, Hydraulic Feed Chippers 813XT

Features may include:
  • 13” high x 18” wide infeed opening
  • Hydraulic dual feed rolls
  • Live hydraulics
  • Auto reverse speed sensing
  • Hydraulic feed roll lift with down pressure
  • 12,000 lb. heavy duty jack
  • Adjustable height exhaust chute
  • 360° hand crank exhaust chute
  • Easy adjust exhaust flap
  • Full engine enclosure
  • Radiator guards
  • Safety Light Package
  • Impeller Safety Lockout
  • Infeed Tray Safety Apron
  • Infeed Tray Safety Bar
  • Dual Emergency Stops On The Infeed Tray
  • SSS Salsco Safety Shield

Photos

Highlights

  • Eldersburg, Maryland
  • 2020
  • Salsco, Inc.
  • Engine Driven, Hydraulic Feed Chippers 813XT
  • Hatz | Kubota
  • Fenders: 3/8” thick steel diamond plate fenders with light enclosures and flag holders
  • Available
  • 7’10” | Infeed Tray: 57”
  • 8’ 7” | Infeed Tray: 33”

Specifications

  • 2020
  • Salsco, Inc.
  • Engine Driven, Hydraulic Feed Chippers
  • 813XT
  • Brush
  • Hatz | Kubota
  • Tier IV
  • 74HP | 74.3HP
  • Single plate or double plate over-center clutch depending on horse power for diesel engine options. Autoclutch on PSI gas engines.
  • One (1) 5-V single back belt. Cast iron pulleys with taper lock centers.
  • Hoses: SAE JIC hose ends & fittings. 3,000 P.S.I. working, 12,000 P.S.I. burst. | Motors: Two (2) Eaton Char-Lynn. One (1) Series H, 14.8 Cu.In.Disp, upper feed roll. One (1) 2000 Series, 29.84 Cu.In.Disp., lower feed roll.
  • One (1) Eaton Gear pump, 5/8” 9 tooth spline shaft, 66 Cu.In.Disp.
  • Two (2), ST225/80R16 LR “E”, 10 Ply
  • 12 v., automotive type, 900 cold cranks. Lockable battery box.
  • Fenders: 3/8” thick steel diamond plate fenders with light enclosures and flag holders
  • 2” x 6” X 1/4” wall rectangular steel tubing.
  • Adjustable height
  • Upper, lower, front & rear housing is 3/8” thick steel. Housings are hinged & held in place by a 13” long x 3/4” diameter pin gauge steel
  • Exhaust Chute: 360º hand crank swivel, height adjustable exhaust chute with easy adjust 12” long directional exhaust flap. Continuous welds & support bar
  • 3” pintle
  • 17’ 6”
  • 7’10” | Infeed Tray: 57”
  • 8’ 7” | Infeed Tray: 33”
  • 24 gallon steel fuel tank
  • 4.6 gallon, with lockable filler cap with dip stick.
  • 7,000 lb. Torflex | 8,000 lb. Torflex
  • 8,260 lbs. (Approximately)
  • Jack: 12,000 lb. capacity heavy duty adjustable height, lockable drop leg, greasable with side wind handle.