2020 Salsco, Inc. Engine Driven, Hydraulic Feed Chippers 818XT
- Year 2020
- Make Salsco, Inc.
- Model Engine Driven, Hydraulic Feed Chippers
- Engine Caterpillar | John Deere
2020 Salsco, Inc. Engine Driven, Hydraulic Feed Chippers 818XT
2020 Salsco, Inc. Engine Driven, Hydraulic Feed Chippers 818XT
Enormous Crush Power!While dual feed rolls are standard, a Quad Feed Roll Option is available. This is a very heavy duty built machine and designed to chip up 18" branches all day, every day with minimum down time. At an infeed rate of up to 103 feet per minute, your crew will have a hard time keeping up with it. All the standard features on this machine are built in to provide the user with a unit that's easy to maintain, safe to operate an and ready to go!
Features may include:- 2” thick x 58” diameter machined & fully balanced impeller with a 7” diameter machined impeller shaft. Approximately 1,700 lbs. 1/2" thick double sided chip blades set in extra wide chip blade pockets to expedite flow through of material.
- Two adjustable, reversible, and sharpenable bed knives. Vines and stringy material will not wrap.
- 1/4" thick steel, 62" wide dirt drop infeed tray allows for dirt, rocks & other non-woody material to filter through before entering the machine. This helps decrease the wear and tear on the chip blades and bed knives.
- 3/8" steel plate impeller housing with an easy impeller housing slide and electric safety latch.
- 3/8" steel, 981 lb. feed roll yoke. Continuous welds & gusseted.
- 2" x 6" x 1/4" wall, rectangular steel tubing trailer frame. Continuous welds, and gusseted cross members.
- 3/8" steel, heavy duty diamond plate fenders with light enclosures, vise mount pads, mud flaps and flag holders
- Impeller Safety Lockout
- Infeed Tray Safety Bar
- Safety Apron On The Infeed Tray
- Dual Emergency Stops On The Infeed Tray
- SSS Salsco Safety Shield
Engine
Engine
Caterpillar | John Deere
Emissions
Tier IV
Engine Power
174 HP | 200 HP
Drivetrain
Clutch
Double plate over center clutch.
Drive System
One (1) 5-V single back belt. Cast iron pulleys with taper lock centers.
Hydraulics
Hydraulic Type
Hoses: JIC hose ends & fittings. 3000 P.S.I. working 12000 P.S.I. burst. | Motors: One (1) Eaton CharLynn “H” series 14.1 Cu.In.Disp.
Pump Type
One (1) Eaton Gear pump 5/8” 9 tooth spline shaft 66 Cu.In.Disp
Wheels & Tires
Tires, Rear Specification
12 x 16.5LT, load range “G”
Battery
Battery
Dual batteries 12 v. automotive type 850CCA in lockable boxes.
Chassis
Mainframe
2” x 6” x 3/8” wall rectangular steel tubing.
Hitch/Type
Adjustable height
Chassis
Fenders: 3/8” thick steel diamond plate fenders with light enclosures, mud flaps, flag holders & vise mount pads.
Dimensions
Adjustability
Exhaust Chute: 360° hand crank swivel, height adjustable exhaust chute with easy adjust 12” long directional exhaust flap.
Dimensions
Infeed Opening: 18” high x 18” wide at the infeed to accept 18” round wood. | Impeller Housing: Housings are hinged & held in place by a 13” long x 3/4” diameter pin.
Coupling
3” pintle
Length
19’
Width
8’ | Infeed Tray: 62”
Height
9’ | Infeed Tray: 43”
Capacities
Fuel Capacity
60 gallon lockable steel fuel tank with pick-up screen, sight gauge, screw cap with dipstick and drain plug. Cushioned.
Hydraulic Capacity
40 gallon steel tank, with pick-up screens, sight gauge with thermometer, drain plug & vented screw cap with dipstick.
Axle Capacity, Rear
8,000 lb. Torflex
Weights
Weight
14,420 lbs. ( Approximately)
Features
Features
Jack: 12,000 lb. capacity heavy duty, adjustable height, lockable drop leg, greaseable jack with side wind handle.