2020 Salsco, Inc. Engine Driven, Hydraulic Feed Chippers 818XT

Information

2020 Salsco, Inc. Engine Driven, Hydraulic Feed Chippers 818XT

Enormous Crush Power!

While dual feed rolls are standard, a Quad Feed Roll Option is available. This is a very heavy duty built machine and designed to chip up 18" branches all day, every day with minimum down time. At an infeed rate of up to 103 feet per minute, your crew will have a hard time keeping up with it. All the standard features on this machine are built in to provide the user with a unit that's easy to maintain, safe to operate an and ready to go!

Features may include:
  • 2” thick x 58” diameter machined & fully balanced impeller with a 7” diameter machined impeller shaft. Approximately 1,700 lbs. 1/2" thick double sided chip blades set in extra wide chip blade pockets to expedite flow through of material.
  • Two adjustable, reversible, and sharpenable bed knives. Vines and stringy material will not wrap.
  • 1/4" thick steel, 62" wide dirt drop infeed tray allows for dirt, rocks & other non-woody material to filter through before entering the machine. This helps decrease the wear and tear on the chip blades and bed knives.
  • 3/8" steel plate impeller housing with an easy impeller housing slide and electric safety latch.
  • 3/8" steel, 981 lb. feed roll yoke. Continuous welds & gusseted.
  • 2" x 6" x 1/4" wall, rectangular steel tubing trailer frame. Continuous welds, and gusseted cross members.
  • 3/8" steel, heavy duty diamond plate fenders with light enclosures, vise mount pads, mud flaps and flag holders
  • Impeller Safety Lockout
  • Infeed Tray Safety Bar
  • Safety Apron On The Infeed Tray
  • Dual Emergency Stops On The Infeed Tray
  • SSS Salsco Safety Shield

Photos

Highlights

  • Eldersburg, Maryland
  • 2020
  • Salsco, Inc.
  • Engine Driven, Hydraulic Feed Chippers 818XT
  • Caterpillar | John Deere
  • Fenders: 3/8” thick steel diamond plate fenders with light enclosures, mud flaps, flag holders & vise mount pads.
  • Available
  • 8’ | Infeed Tray: 62”
  • 9’ | Infeed Tray: 43”

Specifications

  • 2020
  • Salsco, Inc.
  • Engine Driven, Hydraulic Feed Chippers
  • 818XT
  • Brush
  • Caterpillar | John Deere
  • Tier IV
  • 174 HP | 200 HP
  • Double plate over center clutch.
  • One (1) 5-V single back belt. Cast iron pulleys with taper lock centers.
  • Hoses: JIC hose ends & fittings. 3000 P.S.I. working 12000 P.S.I. burst. | Motors: One (1) Eaton CharLynn “H” series 14.1 Cu.In.Disp.
  • One (1) Eaton Gear pump 5/8” 9 tooth spline shaft 66 Cu.In.Disp
  • 12 x 16.5LT, load range “G”
  • Dual batteries 12 v. automotive type 850CCA in lockable boxes.
  • Fenders: 3/8” thick steel diamond plate fenders with light enclosures, mud flaps, flag holders & vise mount pads.
  • 2” x 6” x 3/8” wall rectangular steel tubing.
  • Adjustable height
  • Infeed Opening: 18” high x 18” wide at the infeed to accept 18” round wood. | Impeller Housing: Housings are hinged & held in place by a 13” long x 3/4” diameter pin.
  • Exhaust Chute: 360° hand crank swivel, height adjustable exhaust chute with easy adjust 12” long directional exhaust flap.
  • 3” pintle
  • 19’
  • 8’ | Infeed Tray: 62”
  • 9’ | Infeed Tray: 43”
  • 60 gallon lockable steel fuel tank with pick-up screen, sight gauge, screw cap with dipstick and drain plug. Cushioned.
  • 40 gallon steel tank, with pick-up screens, sight gauge with thermometer, drain plug & vented screw cap with dipstick.
  • 8,000 lb. Torflex
  • 14,420 lbs. ( Approximately)
  • Jack: 12,000 lb. capacity heavy duty, adjustable height, lockable drop leg, greaseable jack with side wind handle.